To finish a rough-sawn mantel and keep the saw marks, don't sand the faces flat. Brush off the loose fibers with a stiff brush, ease the sharp corners by hand, then apply a penetrating oil or a matte clear coat to all six sides, wiping off what doesn't soak in. Test on the back first. Done this way, the beam stops shedding splinters and dust, the color deepens, and every saw mark stays.
Before you start: let it settle
Finish slows the movement of moisture in and out of wood; it doesn't stop it. A green or barely air-dried beam will keep drying under any finish, and checks will open through it. That's fine, but finish too soon and you may want to touch up later.
If you can, bring the beam inside for a while before finishing, and finish it in the room where it will hang or somewhere similar. Work at room temperature; most finishes cure badly when it's cold.
Step 1: Brush, don't sand
A rough-sawn face has loose, torn fibers standing up between the saw marks. They catch dust, snag cloths and make the finish look fuzzy.
Go over every face with a stiff nylon or brass-bristle brush, working with the grain. Brass is gentle enough for softer woods like cedar. Then vacuum or blow off the dust. On a dense wood like white oak, a few passes with a nylon abrasive pad also knocks down fuzz without flattening the marks.
Avoid a power sander on the faces. Even a light pass flattens the high spots between saw marks and leaves a patchy, half-sanded look.
Step 2: Ease the corners
Rough-sawn corners are sharp and splinter easily. Round them over slightly with a sanding block or a sanding sponge at around 80 to 120 grit, just enough to take off the sharp edge. A small, even round on all four long corners makes the beam look finished without looking machined. Do the same to the end edges.
If the ends were cut with a chainsaw or are rough and torn, sand them smoother than the faces. End grain soaks up finish fast and looks dark and blotchy if it's left rough.
Step 3: Decide on the look
There are four common choices. Each keeps the saw marks.
No finish. Raw wood looks great and costs nothing, but it collects dust and soot in the texture and marks easily. Fine for a cedar beam in a rustic room; less so over a fireplace that gets used.
Penetrating oil. Boiled linseed oil, tung oil, an oil-and-varnish blend, or a hardwax oil. Oil soaks into the wood, darkens it slightly, brings out the grain, and leaves a low sheen that keeps the texture. It's the classic look on walnut and oak. Rough surfaces soak up a lot, so expect to use more than you would on smooth wood.
Matte water-based clear coat. A water-based polyurethane or acrylic in a dead-flat or matte sheen changes the color least, so the beam keeps a fresh, pale look. Good for white oak if you don't want it to amber. Apply thin; it can pool in deep saw marks and dry glossy there.
Stain plus a clear coat. Use stain only if you need to match floors or trim. A rough surface soaks up far more stain than a smooth one, so the same stain looks much darker on a rough beam. Test on the back.
Step 4: Test on the back
The back of the beam, the side against the wall, is your test board. Try the finish there, let it dry fully, and look at it in the light of the room. Rough-sawn wood can look very different with finish on it than it does on the can label.
Step 5: Apply to all six sides
Finish every face, including the back and the ends, with the same number of coats. A beam finished only on the front takes on and loses moisture faster at the back, which can bow it. The ends need it most, because end grain loses moisture fastest.
For oil: brush it on generously with a stiff brush, working it into the saw marks. Let it soak for the time on the can, then wipe off everything that hasn't soaked in, with clean rags, pressing into the texture. Oil left on the surface stays sticky. A second coat after it has dried gives a deeper color.
For a water-based clear coat: brush on thin coats with the grain, and go back over the surface after a minute to pick up drips and puddles in the saw marks. Two or three thin coats beat one heavy one.
Oil-soaked rags can self-heat and ignite. Spread each one out flat outdoors until it's stiff, or drown them in a sealed metal can of water, then follow your trash service's rules for disposal. Never leave them wadded up in a pile.
Step 6: Let it cure before the first fire
Let the finish cure as long as the maker says before you light the fireplace, and longer if you can. Oil finishes take days to weeks to cure fully. Fresh finish over a warm fireplace can smell, and it's better to let the solvents leave first.
Species notes
- Walnut: oil makes it glow. Avoid stain.
- White oak: a matte water-based coat keeps it pale; oil warms it to honey. For a darker brown without stain, white oak can be fumed with ammonia, which reacts with the tannins in the wood. That's a job for someone who has done it before.
- Red oak: takes stain evenly; oil gives it an orange-pink warmth.
- Eastern red cedar: often left natural or oiled. Its red fades toward brown in sunlight; a finish with UV protection slows it.
- Cherry and sycamore: can blotch with stain. Use clear oil or a pre-stain conditioner and test.
Our wood species page has more on how each wood looks as a mantel.
Rather not do it yourself?
Finishing a beam takes an afternoon of work plus drying time. If you'd rather hand it off, a furniture finisher can do it; tell them the species and that you want the saw marks kept.
For brushing and texture options on the beam itself, see mantel beams.
Get a Mantel Quote
Tell us the wood and size you want and how you plan to finish it, and we'll quote a mantel to suit.