A solid wood mantel is mounted by fixing steel rods, a steel bracket or a wood cleat solidly to the wall's framing or masonry, then fitting the mantel onto it. Corbels underneath are the other option when you don't mind seeing the support. The method depends on the mantel's weight and what's behind the wall surface, so work those two out first.
Most solid mantels can be hung by a handy homeowner with two helpers. A heavy beam on stone is a job for a carpenter or a mason.
What your mantel weighs
You can work out a beam's weight from its size and species. Multiply the thickness by the depth in inches, divide by 144, and multiply by the wood's weight per cubic foot. That gives pounds per foot of length.
For example, a 6x10 beam of northern red oak at 12% moisture content: 6 × 10 ÷ 144 = 0.42 cubic feet per foot, times about 44 pounds per cubic foot, is about 18 pounds per foot. A 7-foot beam weighs roughly 129 pounds.
For six woods at common sizes, see the weight table on mantel beams. Two things change the real number:
- Moisture. Green wood is much heavier than dry. A green walnut or red oak beam can weigh about half again as much as the same beam dry.
- Leverage. The weight sits out from the wall, so it tries to pull the top fasteners out and push the bottom of the mantel in. A 10-inch-deep beam pulls harder on its rods than a 6-inch one of the same weight.
Plan the mounting for the beam's actual weight, with a good margin, and use hardware rated for it.
Framed wall: finding and using studs or blocking
On a wood-framed wall, everything has to go into wood framing. Drywall alone can't hold a solid mantel, whatever the anchor packaging says.
Wall studs are usually 16 inches apart, center to center, though some walls use 24. Find them with a stud finder, then confirm with a thin nail or a small drill bit where the mantel will cover the hole. Mark the center of each stud on the wall at mantel height. At 16-inch spacing, a 6-foot mantel crosses four or five studs.
If the studs don't fall where you need them, or there's a fireplace chase with odd framing, add blocking: short lengths of 2x lumber fitted between the studs at mantel height and nailed or screwed in. That means opening the drywall, so plan it before you paint.
Lag screws or structural screws go through the bracket or cleat into the center of the stud, deep enough to grip. The hardware maker will say what size and length to use for its rated load.
Brick and stone: anchors and rods
On a solid masonry fireplace, rods or anchors go into drilled holes in the brick or stone. The usual choices are:
- Threaded rod set in anchoring epoxy. Holes are drilled with a hammer drill, cleaned of dust, filled with a masonry anchoring adhesive, and the rods pushed in to cure. Strong and hidden, and the standard way to float a beam on brick.
- Sleeve or wedge anchors for a visible bracket or a ledger board.
Many installers set anchors in solid brick rather than in the mortar joints, which are softer. Whatever you use, check what base material the anchor is rated for, and keep holes back from the edges of bricks and stones so they don't crack.
On veneer, a thin layer of brick or stone over a framed wall, the veneer can't carry the load. The rods have to pass through it into the framing behind, or the mantel needs a different support. If you're not sure which you have, tap around and look at the edges, or ask the builder or a mason.
Our guide How to hang a heavy beam mantel on brick walks through the job step by step.
Hidden brackets vs corbels
Hidden brackets give the floating look. Common types are a steel plate with welded rods that slide into holes in the beam, and a bracket that fits a slot routed in the back of the mantel. They're sold in kits with a weight rating. For a heavy beam, use more rods rather than fewer, and fix each into framing or masonry. See floating mantels for which walls suit which kind.
Corbels are brackets under the mantel, usually wood blocks or iron, fixed to the wall. The mantel rests on them, so the load goes straight down instead of out on rods. They're forgiving: easier to hang, more tolerant of a so-so wall, and good for very heavy beams. They do show, and they add a traditional look that suits some rooms and not others.
A third option is a ledger: a board anchored to the wall that the beam sits on and is screwed to from above or below, hidden by the beam itself.
Whatever holds it, a solid beam keeps drying after it's hung. Fix it so it can shrink a little across its width. Avoid gluing a wide beam tight to the wall along its whole back.
Pre-drilling the beam
Rods need holes in the back of the beam that line up exactly with the rods on the wall. The holes have to be straight, a little larger than the rod, and deep enough for the length the hardware maker calls for. Drilling a 6-inch beam straight and deep is easier on a drill press or with a guide than freehand on the floor.
The usual way is to fix the rods or bracket on the wall first, then make a template of their positions on a strip of cardboard or plywood, and transfer it to the back of the beam. Measure twice; you only get one set of holes.
Who installs it
You have three options:
- Do it yourself. Fine for a light shelf, a cedar beam or a box beam on a framed wall. For anything over about 50 pounds, have at least two helpers and a plan for holding the beam level while it goes on.
- A carpenter. Expect roughly $150 to $500 nationally for the installation alone (national range, not our price); the details are on our pricing page.
- A mason, for stone or brick where the holes need care or the veneer question comes up.
Before anyone drills, check the clearances on our mantel sizing page, and check that the mantel you're ordering fits them.
Get a Mantel Quote
Tell us what your wall is made of and the mantel you want, and we'll quote it and tell you how we'd hang it.