The cleanest way to hang a heavy beam on a solid brick fireplace is on steel rods set in anchoring epoxy: drill holes into the brick, clean them out, glue threaded rods in, let them cure, then slide the beam onto matching holes drilled in its back. Nothing shows, and properly set rods in solid brick will carry a lot of weight. Before any of that, make sure the brick is solid masonry and not a thin veneer, and know what your beam weighs.
Here's the job in order. Read the instructions that come with your epoxy and rods too; their numbers win over anything general.
Step 1: Make sure it's solid brick
A real masonry fireplace is brick or stone all the way through, often several bricks thick around the firebox. Many newer fireplaces are a factory-built firebox with a brick or stone veneer on a framed wall, and some are thin brick tiles glued to backer board.
Clues it's veneer:
- The edges. Look at the sides of the chimney breast and the edges of the hearth. Thin slices of brick instead of whole bricks give it away.
- A metal firebox. Open the doors or remove the screen. Metal side walls, or a metal frame with vents above and below the opening, usually mean a factory-built unit.
- Behind it. From the attic or an adjoining closet, you may see wood framing around the chimney.
On veneer, epoxy rods in the brick have nothing behind them to hold onto. The mounting has to reach the wood framing behind, or the mantel needs another kind of support. A factory-built unit also has its own clearances in its manual.
Step 2: Work out the weight
Weight per foot = thickness × depth (inches) ÷ 144 × the wood's weight per cubic foot. For a 7-foot walnut 8x8 at 12% moisture content: 64 ÷ 144 × 38.5 = about 17 pounds per foot, times 7 feet, about 120 pounds. Other sizes and woods are in the table on mantel beams.
A green beam weighs more than a dry one, and the weight sits several inches out from the wall, so it levers on the rods. Choose rods and epoxy rated well above the beam's weight, and if you're unsure, add a rod.
Step 3: Mark the height and the rod positions
Start 12 inches or more above the top of the firebox opening, the code minimum for a beam on masonry. Mark the bottom of the mantel and draw a level line across the brick with a pencil or painter's tape.
Then mark the rod positions:
- One row of rods, a little below the center of the beam's height. A single row lets the beam shrink in height without fighting the rods. Two rows, one above the other, can split a beam as it dries.
- Evenly spaced, with the outer rods in from each end of the beam so the ends don't sag.
- In solid brick, not mortar. Many installers avoid the mortar joints, which are weaker, and keep holes back from the brick edges so the brick doesn't crack. Check what the anchor maker says about base material and edge distance.
Lay a straightedge or board along the marks and check that the row is level.
Step 4: Drill the brick
Use a hammer drill and a carbide masonry bit of the diameter the epoxy maker specifies for your rod, usually a little larger than the rod. Drill to the depth they call for. Wrap tape around the bit as a depth flag.
Keep the drill level and square to the wall. A wood block with a hole drilled through it, held against the brick, helps guide it. A rod that goes in crooked means the beam won't slide on.
Drilling brick throws fine silica dust. Wear eye protection and a dust mask or respirator, and have someone hold a vacuum nozzle under the hole.
Step 5: Clean every hole
This is the step people skip, and it's the one that decides whether the epoxy holds. Dust left in the hole keeps the adhesive from bonding to the brick. Most makers call for blowing the hole out, brushing it with a round wire brush, and blowing it out again, more than once. Do what yours says.
Step 6: Set the rods
Fit the mixing nozzle to the epoxy cartridge and dispense until the color is even. Fill each hole from the back, pulling the nozzle out as you go, so no air is trapped. Push the threaded rod in with a slight twist until it bottoms out, check that it sticks out the length you planned, and leave it alone.
Cure time depends on temperature; a cold fireplace wall cures slower. Don't load the rods until the full cure time on the cartridge has passed.
Step 7: Drill the beam
Measure the rod positions exactly, or better, make a template: press a strip of cardboard or thin plywood over the rods to mark their centers. Transfer the template to the back of the beam, lining up the bottom edge.
Drill each hole a little larger than the rod and a little deeper than the rod sticks out. Straight holes matter more than anything; a drill press, a doweling jig or a drill guide is worth borrowing.
Step 8: Dry fit, then hang
With two or three people, lift the beam and slide it onto the rods without glue. Check that it seats tight to the brick and sits level. If the brick face is uneven, mark the high spots on the back of the beam and plane or chisel them so it sits flat, or leave a small, even shadow gap.
When it fits, you can put a little epoxy or construction adhesive in the beam holes to lock it on the rods. Keep glue off the back face; a beam glued flat to the brick can't move as it dries. Others skip the glue and let snug rods hold the beam by friction, which makes it easy to take down later.
Step 9: Let it settle
Expect a solid beam to keep drying over the first winter or two, especially over a fire. Small checks are normal. Our guide Will a solid wood mantel crack? explains why, and the mounting guide covers framed walls and corbels if brick isn't your situation.
When to call in help
If the brick is old and soft, the fireplace is veneer, or the beam is more than you and two friends can safely lift, hire a mason or carpenter. Our pricing page has national installation costs.
Get a Mantel Quote
Tell us the size of your brick fireplace and the beam you want, and we'll quote the beam and tell you what it weighs.